Building A Treadle Chicken Feeder

Keep pests away from your chicken's food with this amazingly ingenious feeder!
  1. Gallo del Cielo
    Building a Treadle Feeder
    I like wild birds. I used to feed them on purpose, but now that I have chickens the wild birds have become a cost and potential risk. The wild birds were eating more of my chicken feed than were the chickens. I dealt with the doves with a shade cloth curtain over the chickens' door but the little sparrows were undeterred. They wormed their way straight through the layers of cloth and get inside. Then I worried about all the pests and pathogens vectored by the little beasts. I reduced the risk by feeding outside where they free-range, but if I didn't get the amount just right, the wild birds finished it off. I came to realize that a treadle feeder would be my best solution; it would also allow my birds free access to food. I looked here on BYC and all over the web for various treadle feeders and borrowed many great features to design my own. I've linked videos of treadle feeders in action at the bottom of this page. Also, after building my first feeder, I took note of what I would change and used that to build my second feeder. The only substantive thing that I changed in the second feeder was the treadle-cover assembly. I include the updated plans for the re-designed treadle-cover assembly at the end of this page.

    The Plans:
    I designed the feeder so that it could be largely made from 1/2 sheet of 1/2" plywood, which I had left over from another project.

    [​IMG][​IMG][​IMG]

    Tools Used:
    I used a number of tools to build the feeder, but many are interchangeable with other tools. All the plywood was cut with a circular saw, but a table saw would be better. I cut the treadle, cover, and connecting arms with a chop saw, but any kind of saw could be used. I used a jig saw to cut out the inner lip part, but a coping saw could be used as well. I used 1/8", 1/4' and 1/2" (or larger) drill bits and drill. Finally, I used clamps (4-6) that hold something at least 16" wide, pneumatic nail gun, electric sander, screw driver, hammer, protective eye-ware, tape measure and square. I realize that not everyone has a pneumatic nail gun laying around (the one I used is borrowed), screws could be used instead. You also wouldn't need an electric sander, your birds won't care that it looks smooth (sand the inside lip by hand). In reality, every power tool pictured here could be replaced with hand tools, power tools just make it easier.

    [​IMG]

    Making the Cuts and Assembly:
    I first cut the sheet into two strips, 16" X 48". From those pieces I cut out 4 16" X 16" squares. On two of these squares I drew the lines and cut out the shapes for the two lateral sides. I then took another square and cut off the 4" front piece, being sure to cut it to match the angles of the side pieces. The remaining larger piece became the upper front of the feeder. Another 16" X 16" square became the back. I cut the bottom of the box to fit inside the four walls, this made it about 15" X 16". The remaining 17" X 16" piece was then cut to a width of 8" to use for the top lid.

    Once the main pieces were cut, I put it together using clamps. When temporarily assembled, I measured for the lip insert that will help prevent the chooks from pulling food out. I cut that piece of wood left over from the square used to get the lid. After being cut to size, I measured and drew the inner cut-out and drilled holes at the four corners and cut out the remainder of the center with a jig-saw. A good fit was made by matching the angle long cuts (16") to the angle of the side view.

    [​IMG][​IMG]

    Once it was all together, I started to permanently assemble it. I loosened the two clamps at the back and removed that piece. I glued the two lateral sides of the panel and put it back in, positioning it well and re-clamping it. I then used a pneumatic nail gun to nail it together. I moved to the upper front piece next, loosened the clamps, applied glue, re-inserted, positioned, re-clamped and nailed. I did the same for the bottom front piece and, finally, the bottom panel of the feeder.

    Next, I installed the lip insert for the feeder access area. I rounded the inner edge with sandpaper to make it smoother where the birds might come in contact. Following that, I installed a piece (7" X 15 1/2") of plywood down through the top of the feeder to divide off one smaller section of the hopper. I'll use this separate area to add in extra grainy/seedy treats such as BOSS and I 'll use the larger area for layer pellets. For easier construction, omit the divider. I needed to make a chute to direct the feed to the front of the feeder; so I so cut a piece that was about 11" X 16", cutting at a 45 degree angle along each long (16") side. I cut that into pieces that were 12" and 3.5", to fit into the larger and smaller openings, respectively. I glued those pieces into place.

    [​IMG][​IMG]
    [​IMG]

    To make the lid, I took the lid board (8" X 17") and made a frame around the outside edge using some 3/4" X 3/4" redwood plant stakes I had. I would liked to have used better machined wood, but it was cheap.

    [​IMG][​IMG]

    I'll admit here that I don't know much at all about the physics of the treadle arm connections. In fact, I think I hurt my brain figuring it out. In the end, it seemed much easier than I imagined. I used the same 3/4" X 3/4" redwood to make the arms for the treadle. I started with the top cover and cut two 12" pieces, cut at a 45 degree angle on one end. I took those pieces and clamped them to the sides as they ultimately would be positioned. I then measured this space and added 1/8" to give the arms room for movement. That gave me the width (18 1/4") of the top cover. I then decided that 7 1/2" was enough to cover the feed opening and extend a bit over the front. I cut the 7 1/2" X 18 1/4" cover from an old piece of 1/8" oak veneer that I had left over from rehabbing a table. I then laid out the arms on the cover and clamped, glued and nailed them together. Now that I knew the width, I cut another piece of the oak veneer for the treadle (5" X 18 1/4"). I then cut the arms (3/4" X 3/4" X 17 1/2") for the treadle arms and another ~18 1/4" piece to span the distance between the arms. I glued the veneer to the arms of the cover and the treadle and clamped them until dry.

    [​IMG][​IMG]

    I used screw posts (1/4" #20, 1 1/2" long --Ace Hardware) to connect the cover and treadle to each other and to the feeder. I started by positioning the cover so that the spacing was correct around the front and sides and used washers to keep the gap between the arms and the wall of the feeder. I clamped it in place and drilled the holes for the pivoting hinge. I started by drilling a small 1/8" hole straight through the arm and in through the wall of the feeder. I then enlarged that hole with a 1/4" bit. It was satisfying to find that the cover moved effortlessly once the stud screws were temporarily in place. For the sake of planning the treadle connections, I drew the outline of the cover arm at both the resting and fully opened positions. This will help determine where the connector pieces when the treadle is installed. I repeated the process and mounted the treadle. I determined where the connector arm would need to be placed and drilled the holes for them. Because the screw post hinge head for the connector arm had to be facing inward, I countersunk the hole so that the head would be recessed. Once the screw posts for the connector arms were in place on the cover and treadle, I measured the distance between the two and added 3/4" to each end, cut the arms and drilled the holes.

    [​IMG]

    When I first assembled the mechanism, it worked flawlessly, with one big problem. It took 6 lbs of force to open the cover. My lightest bird weighed 4 lbs. 11 oz. So, I had to move the fulcrum point further back on the treadle arm. I filled the holes with short pieces of 1/4" dowel and the mistake was hardly noticeable. The treadle now requires 2 lbs. 6 oz. to open the cover. I also realized that two of the three potential locations I wanted to keep the feeder sometimes get standing water in our infrequent storms. That could result in the loss or degradation of feed. So, I placed two runners made of 2" X 3"s under each side of the feeder, elevating it off the ground. After I determined that it worked, I disassembled the treadle mechanism and sanded everything. I painted all exterior surfaces with wood sealant left over from building my chicken coop.

    [​IMG]

    [​IMG][​IMG]

    The feeder is probably much larger than I need; it holds a total of 38 lbs of layer pellets. It's also so heavy (20 lbs. empty) that I wouldn't worry about the birds ever tipping it over. I'm going to keep the cover propped open for a couple days while the birds learn how to use the feeder. I don't actually plan to fill the second area with boss, but showed it full for the pic. I usually just give a cup full in the morning and a cup in the evening.
    [​IMG]

    Things I would change:
    I think I made the arms for the cover and the treadle too short. My next feeder would have arms that extend an additional two inches. I also think the treadle could be about two inches wider (7" instead of 5"). The narrowness may be a little awkward for the birds to be so close to the cover as it opens. I might also experiment with using plywood for the treadle itself, rather than the 1/8" veneer, which would make it heavier. Making those changes would allow for less force to be used to open the feeder. I am considering adding a piece of heavy wood to the underside of the treadle. I think I can hide at least 1 lb. of wood there which would reduce the force required to open the feeder to 1 lb 6 oz. On my next feeder I would like to reduce that number to something less than a pound so that smaller chickens could use it.
    I calculated what it would cost to make this feeder if you had to buy the materials. I had all but the screw posts, the most expensive part. I think that you could use something somewhat cheaper, such as bolts or clevis pins. I'm only guessing at the cost for the veneer, it's left over from a project I completed 13 years ago. I knew I'd find a use for that some day. I also didn't figure in costs of sandpaper, washers, glue and waterproofing stain, but those couldn't amount to more than a few dollars.

    Costs:
    [​IMG]
    Keeping wild birds from eating all your chicken feed: Priceless
    [​IMG]



    Here are some videos of treadle feeders in action. I especially love finding videos of feeders made from or inspired by my plans. If you post a video of your birds using a treadle feeder, PM me the link and I'll post it here.






    http://www.youtube.com/watch?v=O01VEoDrkb8&feature=related
    http://www.youtube.com/watch?v=AVGHIqwIWv4&feature=related (talks about training chickens to use treadle feeder)
    http://www.youtube.com/watch?v=nxaM2A_FHcQ (treadle feeder near end)

    _____________________________________________________________________________________________________________________________________________________________________________________________________________________

    Treadle feeder v. 2.0

    I built a second feeder for the yard and addressed the concerns I had after making the first one. I only changed the treadle-cover assembly and made the top part of the lip insert a little wider. The treadle is now wider (7" vs. 5"), which seems a more natural width on which the chickens can stand, bend over and eat their food. I also added a piece of 1/2" plywood (6 1/2" X 17") under the veneer and between the arms of the treadle. It now opens with just 1 lb. 7 oz. of force, so smaller pullets could use it. It takes nearly a full second to close, which provides plenty of time for a chicken to get its head out of the way. Installed and at rest, the cover only weighs 3 oz. If a chicken did get it's head under the lid, it could easily hold it up. I really opens up and closes much more nicely than the first. I also learned through a cabinet maker friend that the screw posts (Ace Hardware) are more commonly known in the industry as "sex bolts". I also found that they can be found online for as low as $0.41. That would significantly reduce the price of the feeder overall, as they were the biggest part of the cost. The other great suggestion my friend made was to use nylon washers instead of metal. The treadle mechanism has to perform hundreds of times a day and who knows how many opening and closing cycles over the lifetime of the feeder and nylon will create less friction and wear than the metal washers would.

    [​IMG][​IMG]


    [​IMG][​IMG]


    *CORRECTION!* In the drawing of the lip insert above, I have the front edge of the lip at 1" wide. That should read, 1 1/2". The extra width to the lip helps to further limit billing feed out of the feeder.


    Update:
    It's been about three weeks now since I've finished the feeders. I started by propping the feeders wide open with a brick on the treadle. I kept them open like this for a week to get the girls used to stepping on the treadle to eat. I stood two cement blocks at the sides of the feeder to limit access from there and force them to step on the treadle. During the second week I propped the cover open so that it closed or opened only about 1" when the chickens stepped off or on the treadle. That got them used to to the movement of the cover mechanism. I now have the cover propped 1/2 way open and the chickens must step on the treadle to access the food. I only prop the feeders open for brief periods of time, usually about 20-30 min in the morning and late afternoon. The rest of the time the chickens can step on the treadle and open the cover and access the food. Two of my birds (EE and BA) quickly learned to fully use the feeder at will. They calmly step up and open the feeder and eat. The others then move in as three can easily eat at once. Typically, they all eat if one of the two birds opens the feeder. I hope to have all 6 up to speed by the end of the week. Having the feeders has had an immediate and dramatic effect on the wild bird population. I now have fewer wild birds visiting my yard than I did before I got chickens. I'm also going through much less food.

    Second Update:
    It's now been over a year since I completed the feeders. All the birds quickly learned to use them, albeit in an interesting way. The chickens learned to use the feeder in an almost perfect rendition of reverse-pecking order; birds lowest on the pecking order learned to use it first and the highest ranking bird learned last. Several others have also reported a similar learning pattern. I just thought that was cool. I was also curious about what would happen when new chicks were hatched and how they would adapt to the feeder. It turned out that they never even approached it until they were about 21 weeks old, in large part because the older birds kept them away while they were feeding. This worked out well as it allowed me to continue feeding the older birds layer pellets without the younger pullets eating them. Then, at about 22 weeks of age, they just suddenly started opening the feeder on their own. That worked out well as they began laying eggs that week. I would also point out that, despite opening and closing the feeder thousands of times over the past year or more, no chicken was ever hit in the head with the closing cover. That seems to be the biggest question I get concerning the feeder.




    Improved plans:
    I want to thank fellow BYC member ajhaig for her most awesome rendering of the treadle feeder plans. I have not yet closely examined all of the measurements, but it's so much more legible than mine that I want to immediately share them here. Thanks again ajhaig!




    [​IMG]



    To the intellectual property thieves: I took the time to make this page so that I could freely share my ideas on how to make a treadle feeder with the BYC community. I did not make this page so that you could manufacture this feeder to sell it or to sell the plans or to take the plans and give them away without giving proper attribution. Doing any of these things is theft.

    Share This Article

Comments

To make a comment simply sign up and become a member!
  1. gg706
    That is AWESOME! Great Job VERY well documented! AND Great Looking! By the way...I LOVE the chicken patiently being weighed while you took the picture! Aren't chickens great?!
  2. Gallo del Cielo
    Thanks! You're right, she was so patient for me!
  3. mamadlh
    Fascinating, thanks for sharing all your hard work!
  4. riverpilot69
  5. dmclalin
    Your skills are amazing!
  6. hereorthere
    Genius!! Thanks for taking the time to take pictures & post them! Can't wait to get started on this chicken project!
  7. momgoose
    Great graphics, description of your experience, and good photos!
    Just one question: Is there a risk of the lid slamming on a chicken if say, the chicken jumps off the treadle onto the lip of the feeder to eat?
  8. Gallo del Cielo
    Thanks! I don't think there's much risk of that happening. I don't believe I've ever seen a chicken step off the treadle completely and onto the lip. If it did happen, the lid closes so slowly and with such little force that it wouldn't be much more than an annoying inconvenience to the chicken, which is probably why I don't ever see it.
  9. Elwood Lightfoot
    Very nice! I think I will have to build one or several LOL
  10. AyeUpChuck
    LOVE this! Cant wait to build some for my coop!
  11. Zootopia
    HHH< DH has a new project!! He's only got himself to blame since he complains about the chickens kicking around the feed. Thanks for the easy plans, this will be a no brainer for him with this.
  12. jdeoliveira74
    you should sell that...thats awesome and you got nicer tools then me:(
  13. Fowlman4
    love it, but need to know, how in the heck did you train that chicken to know there was food available under the lid???
  14. Gallo del Cielo
    I propped open the lid until they learned that food could be found inside---that didn't take long at all. If you look at the the second to last paragraph entitled, "Update," I describe how I trained the chickens to use it.
  15. chickchicky
    Thank you Gallo del Cielo. I built the chicken feeder the following are some of the changes I found I need to change:
    1. Treadle should be 7"x17 1/2"
    2. The cover should be 7 1/2" x 17 1/2 inches
    3. The chute 10" x 15'
    4. The lop insert should be 15" x 8"
    5 The front top 10 1/4" by 16" with a 15 degree angle on the bottom
    Now it is true I am not a carpenter or a cabinet maker just a crafter.
    I also add two 3/4' x 17" slats to the bottom to keep it off of the ground.
    I put another peice of 1/2" plywood on the underside of the treadle as a counter weight
    I will be putting two 1/4" rounds to keep the lid propped up untill the chicken then I will move them down a little to another hole so that the lid will still stay open but have move ment until they are okay with that and then let it close all of the way. Wish me luck!
  16. chickchicky
    Oops sorry about the typos
  17. Gallo del Cielo
    I'm glad you found some measurements that work for you! Good luck training your birds.
  18. NjoyNjoy
    Hi there,
    I have my version of these feeders half built - Since my hens free range, but still need access to feed, I am sick of wasting food to the wild birds, and rodents who scamper along to the tea party too!
    Need to consider the mechanism for the pedal, levers, and food lid. I realise it is like a kitchen rubbish bin pedal system. Unsure HOW and WHAT with the positioning of the two levers, and the joining arm.
    This all has to take into account the wt of the chicken, and the wt of the pedal and lid that it is lifting.
    Any tips of what influences what?
    I have not bought the levers yet, so I haven't played around with it. Don't want to drill holes where they don't belong.
    What tips have you got from your experience?
    thanks.
  19. Gallo del Cielo
    The treadle arm mechanism was the hardest part of the entire project. I tested it before making the feeder by making one side of the mechanism (the three lever parts) and mounted it to cardboard to make sure that everything pushed and opened for the right distance. From that info I made all my adjustments before building the actual mechanism. One thing you want to look for is that the lid should open the right distance for the chickens to get in to eat. You don't have to worry too much about the weight necessary to open the lid. Just be sure that the lid and treadle are about the same weight, perhaps with the lid being slightly lighter. You can make adjustments later by adding weight to the underside of the lid or treadle, as necessary.

    I'm sorry I'm not of much further help. One reason I made the BYC page for the feeder was because of the difficulties I had with this very issue. I'd hoped that others could skip that headache. If it's any consolation, it really wasn't as difficult as I thought it would be. I did end up drilling two holes in the wrong place in my first attempt at the feeder, but they were easily filled and new holes were drilled using what I learned from the first mistake.

    Don't hesitate to ask if you have any other questions, just PM me. Good luck!
  20. ajhaig
    I built it!
    It took a long time as I am a 68 yr old woman (but very handy with tools & AutoCAD). I digitized the plans to fit on one page, with some measurement changes; will try to post it here but if anyone wants a PDF copy, let me know and I will email to you.
    My chickens learned right away, using the intermediate steps outlined in the instructions. I have yet to introduce my 3 new chicks to my original two, but shouldn't have much difficulty according to what is said here and other sites.
  21. Gallo del Cielo
    ajhaig, that is fantastic! I would be very interested in seeing your plans. I'll bet they're much easier to read than mine!
  22. ajhaig
    I tried to reply to Gallo del Cielo's private message but somehow the private message counter on this site isn't working as it says I have reached my max of two messages a day, but I have not sent even one today. Gallo, could you send me your regular email address so I can attach the PDF of the plans I copied from yours?
    Thanks, and your photos were a great help in building it.
  23. nitrobird
    i am getting ready to build mine and would love a set of plans. if you have trouble reaching me thru email this forum link goes straight there. thanks bruce
  24. jggloy
    ajhaig, please email me a copy of the pdf plans.
  25. Iamanegg
    I had to get the Iphone measurement converter to work out inches to centimeters (Australia has the metric system) :) I am looking forward to giving this a go. Thank you for posting it - I reckon it will cost a little more over here, but I will let you know.
  26. tamiw31
    I would LOVE to see a video of the chickens using the feeder!
  27. ajhaig
    Gallo has posted vids in plans above, but here they are again:
    Here are some videos of treadle feeders in action:



    (talks about training chickens to use treadle feeder)
    (treadle feeder near end)
  28. RawrOsaur200
  29. bruceha2000
    Very nice job. I like the idea of a rodent and sloppy chicken resistant feeder. I am wondering why the depth of the feed tray is not shallower. It seems like the birds would have to reach pretty far in and down if the hopper starts to run dry. Maybe they wouldn't be comfortable having their heads in so far?
  30. Gallo del Cielo
    Thanks! The depth is set so that, when full, the feed reaches just about an inch from the top lip. Even when it's nearly empty, they seem quite comfortable reaching in to peck at the last remaining morsels. I think it also helps to keep them from billing out feed. If you think it's too deep, make yours shallower. Post pics and let us know how it works.
  31. sbriant
    hi ajhaig, i would love a pdf copy!
  32. ajhaig
    Hi - there are people asking for a PDF copy of the plans that I digitized, and I am happy to send out but I NEED YOUR REGULAR EMAIL address as this site won't let me attach files on their internal mail system.
    Thanks!
    Arlie
  33. Gallo del Cielo
    The .pdf file of the plans are now uploaded! YAY! Thanks again ajhaig!
  34. hollys chooks
    I built one, finished it today. Have posted photo on my profile. I'll be honest, i didn't follow any of the measurements, just made it up as i went along. To get the treadle mechanism right i used a scrap piece of wood with nails sticking out balanced between the cover and treadle arms to roughly work out pivot points, then drilled pilot holes and checked it worked (again just put thin nails through pilot holes) before screwing it together. Thank you for your info and photos so i could work out how to make it.
  35. Gallo del Cielo
    Fantastic job hollys chooks! I just love it that you found my plans inspiring and worked it out on your own. Well done! It looks like your chooks are already warming up to it. Thanks for sharing with us.
  36. CedarCluck
    So I have to say that I love this design. I am new to raising backyard chickens, and while I do let my birds range in the yard, while I am outside with them, they have a designated run that I just completed building today. But I am having a hard time where my lead hen (named Oprah lol) likes to flip her feed trough over and dump all their feed on the ground. they will pick at the dumped crumbles for awhile, but then they ignore it and it gets mashed in with the bedding. So I am thinking that something like this design would work much better as she wouldn't be able to flip it over so easily (Though I also wonder if they simply don't like the crumbles and would rather pellets, however in my research it seemed as though the crumbles would be easier for them to digest and its also what their previous owner had them on). So heres my question. Is it crucial to the design to have the lip insert? The only reason I ask is because I am not entirely sure if I have enough wood or not ( will be measuring it out on my next day off) though if I do have the wood for it I see no reason not to include it when building it. But really great design! Thanks for posting :)
  37. Gallo del Cielo
    CedarCluck, Thanks for the compliments. Oprah wouldn't be able to flip this feeder over. The purpose of the lip insert is to keep the chickens from billing out feed. The wider the lip, the less chance they can pull feed out and onto the ground. They bill out some from the first feeder with a 1" lip, but not at all from the second feeder with the 1.5" lip. If I were short on wood, I'd make a single 1.5" wide X 16" long piece to place in front and a second piece of similar size and place it at the back of the opening (rather than the cut out shape that I have it above). It would also vastly simplify that part of the project. They'll still be able to bill out at the edges, but it should be minimal.
  38. hollys chooks
    Yes, Gallo del Cielo, that's how i built mine, a piece across the front and back of opening and no food is getting out except inside a chicken. Very nice not having to sweep up mess around the food dish each day. The girls learnt to use the treadle in 5 days. After 4 days of eating out of it left open i needed to hurry them up as i wasn't going to be home for a couple of days. The trick is their favourite treat, bacon rind. I showed the chickens their treat and put it in the feeder, they wandered around it til they figured out how to open it. Repeated it a few times and the next morning they were stepping on the treadle and feeding like they'd done it all their lives. Interestingly, using the treat method the highest pecking order bird learnt first.
  39. Gallo del Cielo
    Exactly, hollys chooks! That's amazing that you trained them so quickly and the top birds learned first. I guess you can never underestimate the power of bacon! LOL!
  40. kukupecpec
    This is incredible! I love building contraptions like this, but I just don't have the space and tools to really work the way I want to! I am definitely jealous!
    Would you be interested in selling them? Because I would buy on in a HEARTBEAT!
  41. old tom
    That's just what I need for my girls. Goin' fishin' at the Gulf for a week and need to coop up the semi-free range (fenced)
    birds. They have no interest in the pellets since we have a bumper crop of crickets and sundry bugs this fall. is there
    any reason not to build this feeder out of Eastern red cedar {Juniperus Virginii)? I have milled up a lot for other projects
    and the plywood might de-laminate with the moisture.
  42. Campesina
    On behalf of all the sparrows I didn't have to kill Than YOU! You are a great example for others in that you chose to share this with your fellow chicken lovers. We just finished ours and installed it in the run but we are sure it will work just fine. Thanks again. Dios te bendiga.
  43. brojrm
    Thanks for all you did with plans and details. I hope to build one . I have been looking at treadle feeders but just cant spend a lot of mula. This is much cheaper and looks better to!!!
  44. chickenlily13
    I built one of these , but they are not water proof! Need to be inside your enclosure so it doesn't get wet.
  45. riverrunner
    Great feeder. Really like the design.
  46. kukupecpec
    wanted to thank you for the awesome plans! I sent this over to my grandpa and he had a blast building one!
    I was wondering if you have any ideas about keeping the birds off the open door? Mine are always jumping on the open door and breaking it off at the arms. It has been lidless for a good month while I try to figure out a better way to stop them from breaking it lol.
    I was also wondering what king of ground you put yours on? My chickens are always piling dirt up under the pedal and then the door won't open lol silly chickens
  47. ajhaig
    You could extend a piece of plywood out from and over the top so when the cover is open, there is no space for them to hop up.
    I put my feeder on a flat surface, like plywood or cement, or block off the edges so they can't move dirt onto or under it.
  48. Teegan92
    Well that is just blimin ingenius!!!
    OK stupid question time................im pretty decent with a hammer and drill but hate sawing.....what do you think the chances are of a thick cardboard one of these? i have pretty small bantams so it would be lighter for them to open...or am i just talking crazy? i suppose the wild birds would be light enough to work it then too? hmm...someone pls let me know, cause i can easily whack one of these together in a day with heavy duty cardboard
  49. Gallo del Cielo
    HI Teegan92! That would really depend on the thickness and durability of the cardboard, but if you can do it, why not try? As expected, there would be hazards from rain, insects and other gnawing creatures, but at least you could decide if you like it. You can make it as hard or as easy to open as you like simply by adding weight to the bottom of the treadle of the cover. Good luck!
  50. Rare Feathers Farm
    I'm looking for 8 of these...in both bantam and LF sizes...can anyone build some for me? I can't even hammer in a nail and I'd rather pay someone to do it for me. LOL I am going to be slapping together from PVC feeders for the winter but will desperately need these next spring...thank you!

BackYard Chickens is proudly sponsored by