Automatic pop door

Date sort Score sort
G-Man

G-Man

Songster
12 Years
Feb 10, 2012
201
12
201
Witter Springs, California
Hi, I've added a few images to my profile page of the Automatic pop door I made. The only thing I still need to do is mount a cover to conceal the motor and electrical outlet. Thanks for looking.

Materials:
1 Veranda .920”X5.250”X12’ plastic/wood composite decking material
1 Add-A-Motor D-20
1 Electrical outlet box to mount inside the frame
1 20 amp electrical outlet
1 Refrigerator switch Servalite 780-101U (this is wired to an outside light to confirm the pop door is operating properly. If the light is on the door is closed, if it's off the door is open)
2 thin 12”x18” zinc coated sheet metal
5/8”X6’ aluminum U channel
7/16”X12”X18” plywood.
1 small eye screw and retainer nuts
1 In-wall programmable timer Honeywell RPL2740B
Contact cement
Misc screws





Updated pics March 22, 2012
 
Last edited:
I would recommend putting a small board on the outside bottom of the door opening that they will step over when open. Basically to stop racoons from being able to get there little paws under your door and lift it up. I was looking to make one myself a couple years ago and remember someone haveing a raccon able to lift it from the outside, so they came up with that fix.

How much did this all cost?
 
Rooster76 said:
I would recommend putting a small board on the outside bottom of the door opening that they will step over when open. Basically to stop racoons from being able to get there little paws under your door and lift it up. I was looking to make one myself a couple years ago and remember someone haveing a raccon able to lift it from the outside, so they came up with that fix.

How much did this all cost?
Click to expand...







Dang, that was a really bad picture I posted. I'll have to take a better one tomorrow.
I read something about raccoon's being able to get their grubby little fingers underneath too. So I used my router to cut a .650 wide and .375 deep dado up both sides and in the bottom plate. This material cut like butter, very easy to work with, and it's waterproof.. I'm looking for other reasons to use this material again.
The Motor is the most expensive component at about $100 shipped. The Veranda material is $17.00 at Home Depot. I had the 1/2" plywood, that I used as the core of the door then skinned it with the sheet metal ($4.97 x 2) on each side. I used the Aluminum "U" channel ($9.39) to give the edges a clean smooth edge to ride inside the dado grooves. I secured it to the wood with screws from the edges, so they wouldn't be seen. The white switch ($12) is wired to an outside porch light on the coop that comes on when the door is closed. Makes for a quick security check.

So to answer you question, you could build it for $136.33 without the switch or $148.33 with. Even cheaper if you just used an 1/8" sheet of sheet metal for the door.

Let me know if you have anymore questions.
 
Last edited:
lesgo54 said:
thats a awesome door setup. thanks for sharing
Click to expand...

welcome-byc.gif



Thank you.
I did plenty of research before I started. I especially liked the one Fleming Outdoors is selling, but with shipping it was more than I was willing to spend.
More rewarding making it myself too. Plus I was able to make a few modifications to suit my needs/wants.
 

Similar threads

Witchychickens
Roosts, pop door, laying boxes
2
Replies
17
Views
3K
Witchychickens
Witchychickens
pcgboca
    • Like
    • Love
Review: Wi-Fi Enabled Automatic Chicken Coop Door by JVR
2 3
Replies
28
Views
20K
Mouthpear
Mouthpear
LizzzyJo
    • Like
Review: Battery powered chicken door! (A+)
2 3
Replies
25
Views
9K
Redsox7715
R
MT45
    • Like
    • Wow
    • Love
Red Heaven Chicken Spa & Resort
2 3
Replies
29
Views
5K
paintedChix
paintedChix
N
Lighting Coop .. open pop door when?
2
Replies
10
Views
2K
Northof26
N

New posts New threads Active threads

Back
Top Bottom