i was just thinking of making something alittle bigger to feed and water my chicks out of when they get bigger well lets see some pics of your holemade feeders and waters
has anyone made there own feeders and waters here
- Thread starter hunter109
- Start date
I know there are lots of good ideas here for feeders and waterers because I've used a lot of them. Unfortunately, I don't have pictures available right now.
The easiest waterer is a 5 gallon bucket with sealable lid. Local bakeries use them for icing, etc. and either give them away or maybe charge $1. Drill 1/2" hole thru the side about 1-2" from the bottom, and seal the lid. I use a funnel to fill it thru the hole or plug the hole with a little stick or something and fill the bucket from the top then put the lid back on. Place the bucket into a larger diameter pan ( I use an old galvanized pan about 4" deep) and there ya go.
I put the one inside the coop on a couple of bricks to keep it out of the litter but the one in the yard is just on the ground.
I've seen this idea made with an automatic filler valve but haven't done that yet so I have to shlep hoses to the coop but thats ok. I only have to refill them once or twice a week,
The easiest waterer is a 5 gallon bucket with sealable lid. Local bakeries use them for icing, etc. and either give them away or maybe charge $1. Drill 1/2" hole thru the side about 1-2" from the bottom, and seal the lid. I use a funnel to fill it thru the hole or plug the hole with a little stick or something and fill the bucket from the top then put the lid back on. Place the bucket into a larger diameter pan ( I use an old galvanized pan about 4" deep) and there ya go.
I put the one inside the coop on a couple of bricks to keep it out of the litter but the one in the yard is just on the ground.
I've seen this idea made with an automatic filler valve but haven't done that yet so I have to shlep hoses to the coop but thats ok. I only have to refill them once or twice a week,
- Thread starter
- #3
i was wondering also if you could use a peice of pvc pipe and fix it for waters and feeders just an idea i have alot of pipe so maybe i could do something with it
- May 19, 2009
- 2,063
- 61
- 173
This is my favorite design. I was lucky enough to find buckets with screw lids from work. I drilled four small holes in the bottom for the feed to fall through, and I drilled a hole in the bottom for a bolt.
I drilled another hole in the middle of a chip/ dip tray (Walmart, 2/$1), and I bolted it to the bottom of the bucket. If I didn't already have a bolt long enough, I would have made two smaller holes and ran clothesline wire through them.
The handle broke off of this one, but I could replace it with a clothes hanger if I wanted to. I could also put it "up on blocks" for the birds. I found that putting it directly on the floor just lets them scratch the food around and waste it.
I drilled another hole in the middle of a chip/ dip tray (Walmart, 2/$1), and I bolted it to the bottom of the bucket. If I didn't already have a bolt long enough, I would have made two smaller holes and ran clothesline wire through them.
The handle broke off of this one, but I could replace it with a clothes hanger if I wanted to. I could also put it "up on blocks" for the birds. I found that putting it directly on the floor just lets them scratch the food around and waste it.
- May 19, 2009
- 2,063
- 61
- 173
Waterers are harder to make, but I have designed a couple in the past. I've put a 2liter soda bottle in a larger bowl, with a small hole in the side of the bottle near the bottom.
Here's a picture of the feeders I made our 16 girls and very easy to fill and move and hardly any waste if any.
Quote:
Here are my designs:
Left is the auto feeder (lots of these with pics on BYC).
Right is the waterer although I should add that I am considering getting some poultry watering cups and building the waterer with those instead of the ball valves and cutouts.
Here are my designs:
Left is the auto feeder (lots of these with pics on BYC).
Right is the waterer although I should add that I am considering getting some poultry watering cups and building the waterer with those instead of the ball valves and cutouts.
Last edited:
- Thread starter
- #8
thanks guys i will try and biuld me some here soon well i hope you all show me a pic of all of your all feeders and waters
CoyoteMagic
RIP ?-2014
Quote:
Here are my designs:
Left is the auto feeder (lots of these with pics on BYC).
Right is the waterer although I should add that I am considering getting some poultry watering cups and building the waterer with those instead of the ball valves and cutouts.
https://www.backyardchickens.com/forum/uploads/85488_water_and_feeder.jpg
OOO OOO Do you have pics of the waterer? Just to give me an idea what it looks like finished. Does it work by vaccum?
Here are my designs:
Left is the auto feeder (lots of these with pics on BYC).
Right is the waterer although I should add that I am considering getting some poultry watering cups and building the waterer with those instead of the ball valves and cutouts.
https://www.backyardchickens.com/forum/uploads/85488_water_and_feeder.jpg
OOO OOO Do you have pics of the waterer? Just to give me an idea what it looks like finished. Does it work by vaccum?
- Thread starter
- #10
i am thinking about useing a 5 gallon bucket for the water but the feeder idk yet
Similar threads
New posts New threads Active threads
-
Latest threads
-
Lost 2 pullets, one left to integrate… how??- Started by BlueberryOatmeal
- Replies: 1
-
-
-
-
-
-
Threads with more replies in the last 15 days
-
-
-
Open Contest Waterfowl & Water Photo Contest
- Started by Kiki
- Replies: 74
-
Ended Official BYC Poultry Caption Contest 05-23-25 Pic by AidKD- Started by TwoCrows
- Replies: 71
-
Solved Attach files picture uploading
- Started by Kiki
- Replies: 62
-
