berettp
Chirping
If I'm using a 2x4 for a roost would it be better to install it flat (4) or vertices (2). I'm in NJ so winters can be cold.
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
I’m going to go yet a different route. Like Howard I’ve experimented. I put 2x4’s flat, 2x4’s on edge, and used tree branches. Chickens are creatures of habit so like to roost in certain places they are used to plus there are locations in the coop they prefer. The spot right in front of the window is prime roosting territory in mine, favored by the more dominant birds. To account for this I shuffled them around after a month or so to give them time to sort things out. Then shuffled them again. My conclusions. People care about this a lot more than chickens do. My chickens were quite happy to use any of them. Where they are in the coop and how high makes a difference. Whether they are 2x4’s flat, on edge, or tree branches doesn’t matter to the chickens.
My tree branches are of varying thickness. They are probably over 3” diameter at one end and less than 1-1/2” diameter on the other. So I flipped them, put the thicker part near the window one time, the narrow part near the window the next time. Guess what. The diameter didn’t matter, location and height did.
I’ve observed mine when they are squatting down in cold weather. Whether they are on a flat surface or the smaller end of my tree branches, their feet disappear in their feathers. Their feet are protected when they squat to roost.
I’ve seen chickens sleep in trees in weather below zero Fahrenheit. They were not perched on a bare dead limb overhanging a bluff squawking defiantly into the teeth of a blizzard. They were in a sheltered valley in fairly thick trees with lots of limbs and could move around to get out of direct winds. These chickens did not have frostbite problems, feet, comb or wattles. You can’t get better ventilation than sleeping in a tree. Decent ventilation with breeze protection allows the chickens to keep themselves warm with their down coat, just like all the birds that overwinter where you are and hide in thickets when the wind is strong and to sleep.
If you decide to use sawn lumber, I fully agree with rounding the corners a bit. I’m not too worried about making the round corners so the chickens can grip more comfortably, though that won’t hurt. I want to get rid of splinters. I hit mine with rough sandpaper.
Whichever you decide will work fine. You’ll make some people on this forum happy if you put them flat, you’ll make other people happy if you put the 2x4’s on edge. You’ll make your chickens happy if you just provide them either way, high enough and with enough length.
Good luck with it. As far as I’m concerned you can’t make a bad decision in this. They all work.
Here’s one version of my main roosts. I normally go with two tree branches but I was down to a small flock at this time. My juvenile roost is a 2x4 on edge. You can get an idea of how their feet wrap around a round roost and maybe a rough idea of size. Maybe that close-up shot will give you an idea of the diameter part of the narrow part.
flat 4" is easier on the chickens feet and allows them to cover all their toes with body heat, in the winter to avoid frost bite! I use flat 4" in mine after reading up on it, I have had no problems with Bumble foot and as far as grasping they get plenty of that on the roost in their run, that are not 2 X 4's!If I'm using a 2x4 for a roost would it be better to install it flat (4) or vertices (2). I'm in NJ so winters can be cold.
Bumblefoot is caused by an open wound exposed to bacteria which can develop into an infection...it has nothing to do with roosts being treated or not.I would add one thought, don't use treated wood at all for roosts - I started with rounded top painted treated wood - it was fine until a couple of my hens wore off the paint on the favored sites and developed mild bumble foot - changing to untreated wood solved the problem. I am totally convinced those roosts were the cause.
Thanks I like the idea of using a branch and I think I will experiment with all the ideas ( food for thought). My coop is modest. I only have four pullets around six weeks and they are using a 2x4 thin side up rounded corners but when sleeping I have seen them start leaning toward as if they are going to fall so being new to this I figured I maybe doing this wrong. I had them start out on 1x1 temp roost when they where younger and they moved up to the larger roost on there own. I am going to swap out the roost with a smaller wooden pole I have to see if they like it. The roost sits infront of a window up higher which seems to be the favoured spot. Thanks again