I will add pictures soon which I am sure will help in forming comments..
FYI: The coop will hold 6 full size hens and I live in CT. (Chicken Breeds: 2 Dominiques, 2 East Eggers, 2 Wyandottes)
There are question built into the summary as well.
THANKS A BUNCH FOR ANY INPUT
Here is what I got to work with on the inside: The coop's approx interior dimensions are 9 by 4.5 feet. (front part of the coop is aprox 6 and 1/2 feet tall and it slopes down towards the back to around 5 feet or so)
I have one 17 x 32 foot slider window installed on one wall. (the long wall)
I have a good size vent that I will add to the highest point in the front of the coop. (the short wall on the front of the coop)
I was thinking of adding another small vent on the same wall as the window. (Most likely the windown screen will get closed in the winter so that second vent will be needed??)
Since the coop was being built from using an existing shed, half the coop remains 'inside'. I basically split the shed right down the center for the coop. Still have 4.5 feet that you can walk into the shed between the shed's ouside wall and the coop's wall. That side of the coop's wall, I put a full door in wide enough for a large broom that you can easily sweep out the shavings and what I call an 'observation' window. I framed out an area with the wall studs and covered it in galvanized wire. Then when I put the plywood over it, I cut a hole in the plywood to match the opening and put that section on hinges with 2 locking bolts. If you ever want to look at the chickens, or give extra air, all you have to do is slide the bolts open and the section of wall drops/swings open to form a 'window'. I can keep this open in the warmer months and since the opening is wired, they will be safe from predators.
For the floor, I framed over the concrete (the entire shed floor was concrete already) and put plywood down. Michele (wife) painted the entire interior of the coop white.
The other thing thats nice, is there is still 4.5 X 13 feet of shed space as well as another 3 or 4 feet of shed space behind the coop's back wall for storage etc..
The only things left to do on the coop exterior are to install the front wall (studs are in place), front wall vent and chicken door and to reinforce/frame the human coop door)
After that, I need to figure out where everything is going to go on the inside of the coop..Roosting pole, nest boxes, food/water etc...(Lots of people are using a board to catch the droppings under the roosting pole.)
Some of the reading I am doing, many people seem to be putting self sticky vinyl tileson the plywood under the shavings..which makes cleaning very easy?
So some questions about the coop itself..
Do I have enough/too many vents?
Any part of the coop need insulation? (I was not planning on this)
Once I get the inside all set, then I plan on building the run next
Here is a rough sketch

FYI: The coop will hold 6 full size hens and I live in CT. (Chicken Breeds: 2 Dominiques, 2 East Eggers, 2 Wyandottes)
There are question built into the summary as well.
THANKS A BUNCH FOR ANY INPUT

Here is what I got to work with on the inside: The coop's approx interior dimensions are 9 by 4.5 feet. (front part of the coop is aprox 6 and 1/2 feet tall and it slopes down towards the back to around 5 feet or so)
I have one 17 x 32 foot slider window installed on one wall. (the long wall)
I have a good size vent that I will add to the highest point in the front of the coop. (the short wall on the front of the coop)
I was thinking of adding another small vent on the same wall as the window. (Most likely the windown screen will get closed in the winter so that second vent will be needed??)
Since the coop was being built from using an existing shed, half the coop remains 'inside'. I basically split the shed right down the center for the coop. Still have 4.5 feet that you can walk into the shed between the shed's ouside wall and the coop's wall. That side of the coop's wall, I put a full door in wide enough for a large broom that you can easily sweep out the shavings and what I call an 'observation' window. I framed out an area with the wall studs and covered it in galvanized wire. Then when I put the plywood over it, I cut a hole in the plywood to match the opening and put that section on hinges with 2 locking bolts. If you ever want to look at the chickens, or give extra air, all you have to do is slide the bolts open and the section of wall drops/swings open to form a 'window'. I can keep this open in the warmer months and since the opening is wired, they will be safe from predators.
For the floor, I framed over the concrete (the entire shed floor was concrete already) and put plywood down. Michele (wife) painted the entire interior of the coop white.
The other thing thats nice, is there is still 4.5 X 13 feet of shed space as well as another 3 or 4 feet of shed space behind the coop's back wall for storage etc..
The only things left to do on the coop exterior are to install the front wall (studs are in place), front wall vent and chicken door and to reinforce/frame the human coop door)
After that, I need to figure out where everything is going to go on the inside of the coop..Roosting pole, nest boxes, food/water etc...(Lots of people are using a board to catch the droppings under the roosting pole.)
Some of the reading I am doing, many people seem to be putting self sticky vinyl tileson the plywood under the shavings..which makes cleaning very easy?
So some questions about the coop itself..
Do I have enough/too many vents?
Any part of the coop need insulation? (I was not planning on this)
Once I get the inside all set, then I plan on building the run next
Here is a rough sketch

Last edited: