Best way to seal?

Oops paint at Home Depot is 9-10 bucks a gallon. I got my porch and floor paint there. It was tinted a very pale grey.
The nearest home depot to me is over an hour away😏. Lowes is about 20 minutes away. But their prices are insane for the paint...especially exterior. For a quart of their cheapest is I think 10 bucks. For a gallon of the same stuff is like 30.
 
The nearest home depot to me is over an hour away😏. Lowes is about 20 minutes away. But their prices are insane for the paint...especially exterior. For a quart of their cheapest is I think 10 bucks. For a gallon of the same stuff is like 30.

They always charge more per ounce for the smaller containers.

They may have a discount section for mis tinted paints too. Can't hurt to look.
 
I've heard of folks using this but I think I read that if it's in an enclosed space it cannot be occupied for 24 hours. Obviously I wouldn't need a 5 gallon pail of it. Maybe 2 at best...when I started looking back before I built this seemed to be the cheapest, "fastest" and most effective way to achieve what I was hoping to do. But real experience versus some experience and some research is best.
You'd need more than 24 hours... very low VOC but it has to dry enough so it's not too tacky, then you'd need to apply a 2nd coat. They have 1 gallon cans which would be enough for a small coop - for my 60 sq ft I used a little less than a 5 gallon can.

Important to read the tech sheet, which specifies temperatures and weather conditions for application: https://cdn.shopify.com/s/files/1/1426/5084/files/TDS_BJ_6080_H18.pdf?373

On the plus side it's more durable than paint and seals up any small crevices very effectively.
 
You'd need more than 24 hours... very low VOC but it has to dry enough so it's not too tacky, then you'd need to apply a 2nd coat. They have 1 gallon cans which would be enough for a small coop - for my 60 sq ft I used a little less than a 5 gallon can.

Important to read the tech sheet, which specifies temperatures and weather conditions for application: https://cdn.shopify.com/s/files/1/1426/5084/files/TDS_BJ_6080_H18.pdf?373

On the plus side it's more durable than paint and seals up any small crevices very effectively.
Why so much for a 60 sq ft coop? Did you go up the entire wall too?
 
Why so much for a 60 sq ft coop? Did you go up the entire wall too?
You use up a bit doing 2 coats (it's much thicker than ordinary paint) plus it's recommended to go about a foot up the walls to maximize waterproofing where you'd need it most (as I have Tyvek on the walls so I only painted up on the studs). I also used it on the bottom of my nest box (so you can't see the legs at all as they blend into the floor) and roost supports.

coop2.jpg


blackdog043 has an article here: https://www.backyardchickens.com/articles/black-jack-rubr-coat-57-for-your-coop-floor.75145/
 
You use up a bit doing 2 coats (it's much thicker than ordinary paint) plus it's recommended to go about a foot up the walls to maximize waterproofing where you'd need it most (as I have Tyvek on the walls so I only painted up on the studs). I also used it on the bottom of my nest box (so you can't see the legs at all as they blend into the floor) and roost supports.

View attachment 2806348

blackdog043 has an article here: https://www.backyardchickens.com/articles/black-jack-rubr-coat-57-for-your-coop-floor.75145/
It makes sense now that you mention it's thicker than typical paint.
 
It makes sense now that you mention it's thicker than typical paint.
Yeah it's not thick as tar, but definitely thicker than paint, which is why stirring it is the most difficult part (blackdog043 suggests turning the can upside down before first use, which is what I did as well). I used a masonry brush to apply it. First coat will look patchy but after you apply the second one it will fill in really well.

I can use a paint scraper on it as well as a metal rake and it doesn't seem to damage it.
 
Yeah it's not thick as tar, but definitely thicker than paint, which is why stirring it is the most difficult part (blackdog043 suggests turning the can upside down before first use, which is what I did as well). I used a masonry brush to apply it. First coat will look patchy but after you apply the second one it will fill in really well.

I can use a paint scraper on it as well as a metal rake and it doesn't seem to damage it.
I like that idea. Is it like a rubberized coat almost like stall mats? Or hard like a spray in truck bed liner
 
I like that idea. Is it like a rubberized coat almost like stall mats? Or hard like a spray in truck bed liner
It's rubberized in that it has some texture/grip to it, but does not provide any additional cushioning like an actual coat of rubber would, so the finished surface is harder like the bed liner.
 

New posts New threads Active threads

Back
Top Bottom