- Thread starter
- #91
- Dec 21, 2009
- 448
- 15
- 121
Thanks for all the kind words folks, please take whatever I have shown here, and use it any way you can.
I've been puttering with finish work this week in between rain showers, but in general I have been taking a break from construction, primarily to let my hands heal, and to attempt to hoe my workshop out.
I did finish the front door and ramp. I talked about raising the end of the ramp to soften the angle in another thread here, and I thought some pics might help.
Recall that this foundation is the height of two 4x4 PT timbers with a 2x4 sill plate on top. I placed about a cubic yard of gravel and tamped it down, then added a cubic yard of sand in 2 batches, tamping and watering it in. It is pretty solid now and the chooks will have no problem scratching up a good dust bath, as well as getting plenty of dietary grit.
I made the ramp from a cedar 1x6, and ripped the treads from cedar board scrap. I glued them with Gorilla glue, and tacked them in place with my air nailer. Gorilla Glue foams and expands, then hardens like a rock, and is waterproof. The treads will probably keep the board from ever bowing.
The coop door I came up with is simple as well. This too is open for revision down the road as experience dictates. For now it is secure and draft free, and will enable me to use the coop as the next-stage brooder once the chicks outgrow the rubbermaid tub. I installed an additional electrical outlet inside the coop, along with a brooder light that is hung over the corner by the closed coop door. It will create a warm spot for the chooks as long as it is needed.
For the door, I cut a couple of pieces of 1/2" scrap plywood for the sides, and ripped a length of 1x3 white pine for rails. I used Gorilla Glue and lots of clamps to install the rails, then cut a plywood door to fit. It was a tight fit on purpose, and sanding the plywood door smooth on both sides where it contacts the rails makes it open and close very smoothly. For now, I simply drilled a hole through rails and door, to fit a locking pin made from a piece of coathangar wire. It locks the door shut and holds it open until I decide on how I want a remote operator to work and where best to put it.
Pretty simple construction and made from leftover scrap. A few screws here and there, some good glue and a bit of stain and paint, and voila!
Since the weather has been unusually warm here, I got a head start on restoring my landscaping in the back yard yesterday. I graded and tossed some grass seed and starter fertilizer out in the yard and the wet weather will get that germinating in no time. I use a lawn food with "natural" ingredients in it as opposed to strictly chemical fertilizer. It dissolves quickly and really builds good grass. By the time the girls are ready to hit the yard, there should be a healthy turf for them to graze on.
I've been puttering with finish work this week in between rain showers, but in general I have been taking a break from construction, primarily to let my hands heal, and to attempt to hoe my workshop out.
I did finish the front door and ramp. I talked about raising the end of the ramp to soften the angle in another thread here, and I thought some pics might help.
Recall that this foundation is the height of two 4x4 PT timbers with a 2x4 sill plate on top. I placed about a cubic yard of gravel and tamped it down, then added a cubic yard of sand in 2 batches, tamping and watering it in. It is pretty solid now and the chooks will have no problem scratching up a good dust bath, as well as getting plenty of dietary grit.


I made the ramp from a cedar 1x6, and ripped the treads from cedar board scrap. I glued them with Gorilla glue, and tacked them in place with my air nailer. Gorilla Glue foams and expands, then hardens like a rock, and is waterproof. The treads will probably keep the board from ever bowing.

The coop door I came up with is simple as well. This too is open for revision down the road as experience dictates. For now it is secure and draft free, and will enable me to use the coop as the next-stage brooder once the chicks outgrow the rubbermaid tub. I installed an additional electrical outlet inside the coop, along with a brooder light that is hung over the corner by the closed coop door. It will create a warm spot for the chooks as long as it is needed.
For the door, I cut a couple of pieces of 1/2" scrap plywood for the sides, and ripped a length of 1x3 white pine for rails. I used Gorilla Glue and lots of clamps to install the rails, then cut a plywood door to fit. It was a tight fit on purpose, and sanding the plywood door smooth on both sides where it contacts the rails makes it open and close very smoothly. For now, I simply drilled a hole through rails and door, to fit a locking pin made from a piece of coathangar wire. It locks the door shut and holds it open until I decide on how I want a remote operator to work and where best to put it.




Pretty simple construction and made from leftover scrap. A few screws here and there, some good glue and a bit of stain and paint, and voila!
Since the weather has been unusually warm here, I got a head start on restoring my landscaping in the back yard yesterday. I graded and tossed some grass seed and starter fertilizer out in the yard and the wet weather will get that germinating in no time. I use a lawn food with "natural" ingredients in it as opposed to strictly chemical fertilizer. It dissolves quickly and really builds good grass. By the time the girls are ready to hit the yard, there should be a healthy turf for them to graze on.
