A few days back I found evidence that the coons had somehow managed to get past my primary electric fence to raid a small patch of sweet corn. No real surprise, as primary fence only surrounds the secondary area on only 3 sides. Fourth side is chain link fence which is primary yard for the birds. There is a gate that opens up between them. Coons have either managed to get past the electric fence, or else go under or over two sections of chain link fence, which is the most likely avenue of entry. Anyway, I wanted to construct a temporary electric fence to protect what is left of my sweet corn. Sort of a belt and suspenders approach. This one is closed in on all four sides. A hot fence within a hot fence. Double jeopardy! Will be curious to see if they get past it.
For this one, I used the poly tape fence material (has strands of stainless steel wire woven into the tape), as I had it around and I wanted it visible for human pedestrians. Entire process took maybe all of one hour to construct. Four steel post corners, set insulators, stretch the tape then prop it up on step in poly posts made for these light duty fences. Could have used the poultry netting, which would have been more effective, but this area was larger than what 160 linear feet would surround. Tape fence of this type is almost as easy to setup and costs far less than poultry netting does.
Spacing is 5" off the deck, then 2nd wire 5" above that. Coons typically try to crawl between the two, so may get it from above, below.....or both. They don't know it is a HOT fence, so don't know to avoid it until it's too late.
So here is the charger......running on a freshly charged battery. This is a 12 volt unit made by Parmak in Kansas City, and sold as a rebranded unit by our local farm coop. (MFA to those in MO who might want to know). Cost of these runs about $100. Battery charge lasts 2 or 3 months, depending on how clear you keep the fence.
On on a fresh charged battery, gauge on needle is maxed out. So how hot is it?
That is X1000, so 13,300 volts. Ouch.
And on the END of the poly fence run? (Test the end, farthest away from the connection......if it is HOT there, it has to be hot all along the way getting there)
A digital tester of this type is one of the best diagnostic tools you can have when messing with a fence. It tells you all you need to know.......and not the hard way.
So will this work? We will see. Probably won't know what happens unless I find the fence down on the ground (somebody got it!)......or else no more damage to the corn.
Bottom line is a fence of this type is quick, easy and effective. If I was to make it permanent, I'd opt for 17 gauge aluminum wire instead of the poly tape. Or if this was intended for full size bears (not these mini-bears), tape or rope would be a good idea as they are more visible.
For this one, I used the poly tape fence material (has strands of stainless steel wire woven into the tape), as I had it around and I wanted it visible for human pedestrians. Entire process took maybe all of one hour to construct. Four steel post corners, set insulators, stretch the tape then prop it up on step in poly posts made for these light duty fences. Could have used the poultry netting, which would have been more effective, but this area was larger than what 160 linear feet would surround. Tape fence of this type is almost as easy to setup and costs far less than poultry netting does.
Spacing is 5" off the deck, then 2nd wire 5" above that. Coons typically try to crawl between the two, so may get it from above, below.....or both. They don't know it is a HOT fence, so don't know to avoid it until it's too late.
So here is the charger......running on a freshly charged battery. This is a 12 volt unit made by Parmak in Kansas City, and sold as a rebranded unit by our local farm coop. (MFA to those in MO who might want to know). Cost of these runs about $100. Battery charge lasts 2 or 3 months, depending on how clear you keep the fence.

On on a fresh charged battery, gauge on needle is maxed out. So how hot is it?

That is X1000, so 13,300 volts. Ouch.
And on the END of the poly fence run? (Test the end, farthest away from the connection......if it is HOT there, it has to be hot all along the way getting there)

A digital tester of this type is one of the best diagnostic tools you can have when messing with a fence. It tells you all you need to know.......and not the hard way.
So will this work? We will see. Probably won't know what happens unless I find the fence down on the ground (somebody got it!)......or else no more damage to the corn.
Bottom line is a fence of this type is quick, easy and effective. If I was to make it permanent, I'd opt for 17 gauge aluminum wire instead of the poly tape. Or if this was intended for full size bears (not these mini-bears), tape or rope would be a good idea as they are more visible.