Attaching hardware cloth for the run.

[CrystalMosko]

Hi Everyone! My hubby is getting ready to put the run together. I think it's going to be 10'x16'. We will be using pressure treated lumber. My question is in between the posts, how do you attach the cloth to eachother? You run it vertical, correct? I thought I read on here somewhere how there is a trick to it, but now I can't seem to find that thread. Anyhow....tips would be much appreciated! =) Thanks

 

[aart]

Yes, plan your framing to match your HC.

 

[david3355]

Hi Everyone! My hubby is getting ready to put the run together. I think it's going to be 10'x16'. We will be using pressure treated lumber. My question is in between the posts, how do you attach the cloth to eachother? You run it vertical, correct? I thought I read on here somewhere how there is a trick to it, but now I can't seem to find that thread. Anyhow....tips would be much appreciated! =) Thanks

I ran mine horizontal. 4ft. Put 2x6 horizontally between posts every 4ft. 2x4s would work fine too. Used medium to large staples. Type that is hammered in.
Also bottom section is about 3ft, giving a foot of skirting if you don't want to do a full 4 ft of skirt. I had enough left over I overlapped for 4ft of skirting.

 

[3KillerBs]

We ran ours vertical, having planned to have posts every 4 feet so that the 48" wire would reach, except for one wall where we ran it horizontally and planned a horizontal board in the right place. The reason we did it that was was to be able to cut lengths of wire that were easier to handle on our very large coop.

You can see how we did it on my build thread starting here: https://www.backyardchickens.com/threads/large-open-air-coop-in-central-nc.1443812/post-24727971

We used a pneumatic fence stapler, which was wonderful to have.

I used screws with fender washers on a different structure.

 

[mowin]

I'd build it with post set to match the width of the HC run vertical, as 3kb mentioned above. This method works great with wide rolls of HC.

However if you purchased 2' wide HC, that's a lot of additional posts to set. I'd then run the HC side to side and add a horizontal 2x4s every 2’ so the seams fall on the 2x4s.

 

[21hens-incharge]

I saved the wire that is wrapped around the rolls of hardware cloth to weave/sew two pieces together.

Another option would be "J" clips or cage clips if using 1/2" hardware cloth. They are a bit fiddly to get the hang of but work well.

This is what mine looked like. I see there are several more options these days.

https://www.amazon.com/LITTLE-GIANT...wicXNhIjoiNC41NiIsInFzcCI6IjQuNjIifQ==&sr=8-8

https://www.amazon.com/Miller-Manuf...icXNhIjoiNC41NiIsInFzcCI6IjQuNjIifQ==&sr=8-15

 

[MACCanadianCoop]

I framed the run posts just shy of 4 feet apart so that I could attach the HC directly to the posts. On the one end where I didn't have a post, I overlapped the HC by a few inches and then used zip ties to secure the two pieces together

 

[CFLRanching]

We've always just laid it side by side and overlapped (the part we're adding to). So the part where the cut end comes up through your little square and wraps around we typically put that part on the bottom and use needle nose pliers to bend around the previously cut portion. Then we fasten it to our wood with fender washers and star-head deck screws (if larger boards) and anything smaller, woodwise, with a screw that has a wider, flat head (but philips type head) and that way it catches the square guaging and holds it in place. We've also used roofing type screws (not self tappers) with a hex-head since they already have an attached washer. You can see both types of screws in this picture (zoom in). Philips head type with the flat wide head are going up the side (they're about 1/2" long).

 

[raingarden]

https://smile.amazon.com/Keadic-Gal...x=hog+rong+3/8+inch+galvanized,aps,479&sr=8-8

 

[RubySue]

I framed the run posts just shy of 4 feet apart so that I could attach the HC directly to the posts. On the one end where I didn't have a post, I overlapped the HC by a few inches and then used zip ties to secure the two pieces together

Hello did you use plastic or steel zip ties?